Olixar Huawei P20 Pro Tempered Glass Screen Protector Reviews
- Russian & English ( 69)
- All languages ( 79)
- French ( 8)
- Spanish ( 1)
- English ( 69)
- Portuguese ( 1)
Showing 1- 10 of 79reviews ( )
There are more reviews in other languages. Show all languages to see more reviews and we can translate them for you.
Mobile Zap customer support was excellent in response to my dissatisfaction.
Researched all the reviews, this product got outstanding feedback from customers, I bought one and am really happy with it, outstanding quality
- edges of glass arent rounded and are fairly sharp
- under sunlight a dotted pattern will show on the glass (assuming its the adhesion)
- from time to time it will look like water or oil is underneath the screen making slightly colourful and weird patterns. It responds to the touch (changing shape) but it barely noticeable when the screen is on.
Overall the negative aspects of this product arent very noticable through daily use but I would not come back for the same product again.
I already recommended the site to colleagues. :)
There seemed to be a residue behind the screen guard. Assuming I had incorrectly installed the first one, I removed it and installed the second one. The problem however persisted.
It was only afterwards that I read that these protectors are slightly curved. It is this design flaw which creates a minute air gap between the protector and the phone screen. This air gap causes refraction of light leading to a rainbow-like oily haze under the screen guard, centered in the middle of the screen.
This residue by no means diminishes the protection. But, everytime I unlock my phone , I find my attention drawn to this flaw.
I hate the cheap plastic ones as they never fit without a single bubble, but this is just not worth the money as it cracks to easily.
Super communication from mobilefun!
The small camera gap at the top actually ends up covering the camera lens! Also let's in dust on the sides.
Otherwise it is fit for purpose.. Very strong and good value for money.
I can recommend in 100 % to everyone who has huawei p20 pro. Thank you mobilefun for fast dispatch and high quality service.
Fitting tip: The hole in the black mask for the notification light is very small and requires very accurate alignment. You can make this easier by plugging the phone into a charger to illuminate the light which makes it easier to position the protector correctly.
Tip 2: It shouldn't be necessary, but if you find the protector reduces the touch sensitivity, go into the settings and turn 'Gloves Mode' on. This increases the distance over which the screen will register a touch.
Tip 3: At least one reviewer mentioned the matrix of tiny dots visible under the screen. These are to assist fitting (they prevent immediate full adhesion allowing some re-positioning). When you are happy with the positioning, make sure that you smooth out the screen by pressing firmly (but NOT hard) across the whole screen area several times. Over the next few days you will then find that the matrix of dots then all but disappears completely.
I made the mistake with the first one I bought.
100% My fault though.
So it turns out to be cheap rubbish. Do not buy!
Well over priced.
Unlike glass protectors I've used for other phones, the p20 pro protector only sticks to the screen around the edge and not all over the screen. Dust builds up quickly and eventually, in a couple of weeks or so causes the protector to lose its stickiness. This has happened on three protectors I've fitted. The first place this build up happens is around the notch, the top of the notch is the adisives weakest point.
I had to remove it all together has I was worried that it would let dust/ dirt bye and scratch the glass,so know I have lost money and not to happy with this product.
I follow the instructions, did exactly as told and the protector was place really good and firm.
But after few day (not even a week), the protector started to show bobbles of air, and start to fall apart. The top draw i find it really hard to pull down with protector, the corners of the phone are almost impossible to press with protector.
Now i don't know why, but i won't judge, but the price and the result are bit high and costly (for the days that the protector survive).
I bought 2 of this protector just to try, hope the second one will work better.
The screen protector is supplied with some cleaning wipes but if you keep the plastic screen protector supplied with the 'phone on until you replace it the surface doesn't need any preparation.
Shame because was all most perfect
But tanks anyway
There are a couple of downsides that mean I won't buy this again - but they're personal preferences.
First is the notch. This screen protector covers it completely so you will have to turn it off in our display settings. To me, it's a shame as I was loving the look of the notch. Also, if you don't fit the protector perfectly you will see some icons from the notch poking through.
The second negative from me is how it makes the fingerprint scanner difficult to use. It makes it slightly more difficult to recognise your print as it's now partially "recessed". Whereas without the protector on, the fingerprint sensor is flush with the screen.
If you can look past these negatives then I'd recommend it. I personally won't buy one again but I can't knock the build quality!
Sorry, no matching reviews have been found. Please check the filters you have applied.
Please check the filters you have applied or you can Show all languages to see reviews and we can translate them for you.